Gbc 44DT Manuale Utente

44DT LaminatorINSTALLATION & OPERATION MANUALDocument Number: 930-122 REV: - REV DATE: 11-24-04Do not duplicate without written permission.

Operating InstructionsPage 3-244DTFCC NOTEThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Page 4-1Operating Instructions44DTThis chapter describes how to install the machine. There are no operator serviceable parts to the machine other than

Operating InstructionsPage 4-244DT

Page 5-1Operating Instructions44DTTOP FILM SUPPLY SHAFTHolds the film supply on the laminator.RELEASE LINER TAKE-UP Rewinds the release liner of pressu

Operating InstructionsPage 5-244DTFEED TABLEThe feed table is used to position items for laminating and mounting. When the feed table is removed, the

Page 5-3Operating Instructions44DTFILM AND TAKE-UP TENSION ADJUSTMENT KNOBSFig. 5-4. Tension Adjustment Knobs.Allows the operator to increase or decre

Operating InstructionsPage 5-444DTIMPORTANT: To change from a process where only the top roller is heated to a process that requires heat on both roll

Page 6-1Operating Instructions44DTThis chapter describes how to use the laminator to:Operate the machineLoad films (web the machine)Laminate itemsMoun

Operating InstructionsPage 6-244DTSet the desired speed. Refer to the Lamination Guide chapter.Press the RUN button. The rollers will begin to turn.

Page 6-3Operating Instructions44DTIMPORTANT: The top and bottom rolls of laminating film must be the same width. Always change the top and bottom suppl

Operating InstructionsPage 6-444DTREMOVING AND INSTALLING THE FEED TABLEThe feed table should not be removed except to install films. When the table i

Page 6-5Operating Instructions44DTRemove the release liner from the take-up core by doing the following.Lift the right end upward and out of the suppo

Operating InstructionsPage 6-644DTInsert the bearing end of the shaft into its support on the right side of the machine, press to the right, and then

Page 6-7Operating Instructions44DTFig. 6-9. Configuration for Thermal Film.Fig. 6-10. Configuration for AccuShield FilmCONFIGURATION FOR PSA FILMSPSA fi

Operating InstructionsPage 6-844DTLOADING FILM WITH A THREADING CARDThe following procedure uses a film threading card that is sometimes provided with

Page 6-9Operating Instructions44DTPress the straight edge of the threading card into the two films at the nip (the point between the two pressure roll

Operating InstructionsPage 6-1044DTFig. 6-18. Threading Card Inserted Into the Film.Press the RUN button on the control panel.Move the roller pressure

Page 6-11Operating Instructions44DTWhile pulling evenly, carefully align the edges of the mounting film (or kraft paper) with the laminating film, and

Operating InstructionsPage 6-1244DTTACKING NEW FILM TO EXISTING FILMThe following describes a method for loading thermal or PSA film whereby the existi

Page 6-13Operating Instructions44DTDECALING IN TWO PASSES WITH PSA FILMDecaling is where you laminate items and then mount them on other materials suc

Page iOperating Instructions44DT1. SafetyWarnings ...1-1General ...

Operating InstructionsPage 6-1444DTPress RUN and immediately grasp the release liner for separation as the board is pulled into the rollers. Do not a

Page 6-15Operating Instructions44DTFILM ALIGNMENT AND TENSIONFILM ALIGNMENTThe top and bottom supply rolls must be aligned as closely as possible. Mis

Operating InstructionsPage 6-1644DTCLEARING A FILM JAM (WRAP-UP)Film jams (wrap-ups) may occur if the film is loaded backwards or if the area at which

Page 7-1Operating Instructions44DTCARING FOR THE 44DT LAMINATORThe only maintenance required by the operator is to periodically clean the rollers. The

Operating InstructionsPage 7-244DTTROUBLESHOOTINGSymptom Possible Cause Corrective ActionPower lamp does not illuminate (next to the stop button when

Page 7-3Operating Instructions44DT

Operating InstructionsPage ii44DT

Page 1-1Operating Instructions44DTYour safety, as well as the safety of others is important. Before you install or use the machine, read and follow al

Operating InstructionsPage 1-244DTDo not insert objects unsuitable for lamination or expose the equipment to liquids.ELECTRICALThe laminator should be

Page 1Operating Instructions44DTLIMITED 90-DAY WARRANTYThe Manufacturer warrants to the original purchaser for a period of ninety days on labor and on

Operating InstructionsPage 244DT

Page 3-1Operating Instructions44DTOperating SpeedVariableFixed – Safety shield removed••2.5 to 10 fpm (0.8 to 3 mpm)3 fpm (0.9 mpm) DimensionsWidthHei